Introduction to WDM Transponder

by www.fiber-mart.com

With the development of wavelength-division multiplexing (WDM) technology, the network traffic volume is increasing and the demand for more network bandwidth is also on the rise. By converting the operating wavelength of the incoming bitstream to an ITU-compliant wavelength, WDM transponder serves as a key component in WDM system. As an important technology in the fiber optical network, WDM is moving beyond transport to become the basis of all-optical networking. And how to optimize WDM network has always been a hot topic. The transponder is a device to optimize the performance of WDM network, which plays an important in the whole system of WDM network. This article will introduce you the information on WDM transponders.

 

What Is WDM Transponder?

Also called as an OEO (optical-electrical-optical) transponder, a WDM optical transponder unit is an optical-electrical-optical wavelength converter, which has been widely adopted in a variety of networks and applications. The picture below shows us how a bidirectional transponder works. In this picture, the transponder is located between a client device and a DWDM system. And we can see clearly that, from left to right, the transponder receives an optical bitstream operating at one particular wavelength (1310 nm), and then converts the operating wavelength of the incoming bitstream to an ITU-compliant wavelength and transmits its output into a DWDM system. On the receive side (right to left), the process is reversed. The transponder receives an ITU-compliant bit stream and converts the signals back to the wavelength used by the client device.

 

The Application of a WDM Transponder

According to its function, the application of a WDM transponders can be classified into the following types.

 

Wavelength Conversion. It is known to us that when a CWDM Mux/Demux or DWDM Mux/Demux is added into a WDM network, there is a requirement to convert optical wavelengths like 850nm, 1310nm and 1550nm to CWDM or DWDM wavelengths. Then the OEO transponder comes to assist. The OEO transponder receives, amplifies and re-transmits the signal on a different wavelength without changing the signal content.

 

Fiber Mode Conversion. Multimode fiber optic cables (MMF) are often used in short distance transmission, while single-mode fiber optic cables (SMF) are applied in long optical transmission. Therefore, in some network deployment, considering the transmission distances, MMF to SMF or SMF to MMF conversions are needed. WDM transponders can convert both multimode fiber to single-mode fiber and dual fiber to single fiber.

 

Signal Repeating. In long haul fiber optic transmission, WDM transponder also can work as repeaters to extend network distance by converting wavelengths (1310nm to 1550nm) and amplifying optical power. The OEO converters convert the weak optical signals from the fiber into electrical signals, and regenerate or amplify, then recover them into strong optical signals for continuous transmission.

 

WDM Transponder and FMT Solution

At fiber-mart, OEO transponders are made into small plug-in cards to be used on the FMT platform. FMT platform makes devices like EDFA, OEO, DCM, OLP and VOA into plug-in cards and provides standard rack units as well as free software to achieve better management and monitoring. In addition, FMT series products like OEO, DCM and OLP also have higher performance than that of old ones. FMT series OEO transponder can convert optical signals into DWDM wavelengths, reducing the fault risk caused by high power consumption of DWDM fiber optic transceiver. Since the OEO transponder is made into small plug-in card in the FMT platform, it only occupies one slot in the special designed chassis when installed, thus saving a lot of space. In addition, all these FMT plug-in cards, including OEO, in a rack unit share the same power source and support hot plug & play operation. And they can be inserted or removed flexibly in the racks for DWDM networking.

 

Conclusion

Since the OEO or WDM transponder plays an important role in WDM network, such as receiving, amplifying and re-transmitting the signal on a different wavelength, adding an OEO transponder into the WDM network is very essential. The OEO transponders in our FMT series are made into small plug-in cards with high quality to ensure good transmission performance. For more information on our FMT system, please visit www.fiber-mart.com.