MPO cable Archive

---

FHX Ultra High-Density Fiber Patching Solution

In today’s data centers, space is often at a premium, making density more critical than ever. So using a comprehensive solution of high-density fiber enclosures with either adapter panels or fiber cassettes would provide a complete fiber cross connect patching solution for applications where maximum density is required. The topic [ Continue reading…]

---

Customer Guidance on Variable Optical Attenuators

Speaking of a variable optical attenuator (VOA), people may know something about it. But asked to define a variable optical attenuator, they hesitate, and some of them may say it is just a simple device to reduce the signal power. Few of them can tell you the importance and principle of a variable [ Continue reading…]

---

---

Introduction of OP-2000C Fiber Optic Polishing Machine

Introduction of OP-2000C Fiber Optic Polishing Machine optical Fiber Polisher, OP-2000C is corner pressure polshing machine for fiber connectors. Key Features: Can polish 24~40 connector at same time, very applicable to bulk production. Polish process using liquid crystal display, can display the time polish, polish speed and polish times, making the process [ Continue reading…]

---

Introduction of AFCM-2000 Automatic Fiber Cable Cutting Machine

Description and Features: Automatic Opical Fiber Cutting Machine is applied for producing fiber optic patchcord, and it is a professional equipment with measuring length / cutting and winding fuctions. It could cut different indoor optical fibers into required length and wind cable into circularity. This equipment integrates the advantages from China and oversea factory’s [ Continue reading…]

---

Arista 7050QX Series Switches Compatible Optics

Arista 7050 series is the main configuration for today’s 10GbE and 40GbE data centers. The emergence of Arista 7050X series has greatly increased the performance, scalability, density, power efficiency for software and cloud networking. Under the family of Arista 7050X, there are three family branches of 7050QX, 7050TX and 7050SX. In [ Continue reading…]

---

---

Development of SFP Transceiver for DWDM Applications

Introduction   Dense wavelength division multiplexing (DWDM)transmission systems, which have conventionally been adopted in long-haul backbone networks, are now being adopted in metropolitan area networks along with the recent rapid spread of multimedia services as typified by the Internet. In the applications for metropolitan area networks, the small form-factor pluggable [ Continue reading…]

---

How to Use Single-Fiber CWDM MUX/DEMUX

In CWDM networks, dual-fiber CWDM MUX/DEMUX, which uses the same wavelengths for transmitting and receiving, is usually used in dual way transmission applications. The working principle is easy to understand. A duplex fiber cable links two dual-fiber CWDM MUX/DEMUXs supporting the same wavelengths installed on each end of the fiber optic [ Continue reading…]

---

Raman-off gain 10dB FM-RA Series Raman Amplifier

Raman-off gain 10dB FM-RA Series Raman Amplifier Raman-off gain 10dB FM-RA Series Raman Amplifier is high power Raman Amplifier which is used in low noise, Long span or high speed Optical Transmission system. Using transmission fiber as the gain medium to form distributed to enlarge, reduce system noise and will [ Continue reading…]

---

Introduction of SUNMA OP-5000 Fiber Polishing Machine(MPO/ MTP)

The 5000 also has fully programmable pressure and speed ramp rates for slow starting the polishing process. It also has programmable film change counters and maintenance section for alerting operators when to change film or provide service to the machine. If the number of connectors loaded into the polishing fixture [ Continue reading…]

---

How to Measure Fiber Optic Network by Using OTDR Testers?

How to Measure Fiber Optic Network by Using OTDR Testers? Optical fiber measurement can be divided into three steps: using OTDR testers for parameter setting, data acquisition and analysis. Measuring parameters include artificial Settings. (1) the wavelength selection (λ): Because of different wavelengths corresponding to different features (including attenuation, slightly curved, etc.), [ Continue reading…]

---